Warehouse safety + rack protection
Protection built around real warehouse traffic
Coordinate rack guards, barriers, bollards, pedestrian separation, and structural protection around the vehicles, people, equipment, and fixed assets moving through an active facility.
Protection systems
Put protection where movement creates exposure
The useful solution depends on what may be struck, which equipment is operating nearby, how pedestrians move through the area, and the clearances and anchoring conditions at the site.
01 / Racking Rack Protection Systems
Post protectors and aisle-end guarding coordinated with rack geometry, traffic, and operating clearance.
02 / Separation Guardrails + Safety Barriers
Physical separation around storage, work areas, infrastructure, equipment, and designated travel paths.
03 / Fixed assets Warehouse Bollards
Visible fixed guarding for corners, entrances, equipment, utilities, and other exposed facility assets.
04 / People Pedestrian Safety Systems
Walkway barriers, gates, and crossings coordinated with visibility, work areas, traffic, and egress.
05 / Infrastructure Column + Structural Protection
Guarding around building columns, supports, door frames, and other critical fixed infrastructure.
06 / Conflict zones Impact + Traffic Control
Combined guarding, markings, gates, and visual cues organized around high-conflict operating areas.
Before selecting a barrier
Map the movement and the exposed assets
Start with the operating routes and known conflict points, then account for pedestrians, protected assets, working clearances, the slab, and any site-specific requirements. Product selection and anchoring require project-specific review.
Review design + layout support- 01
Traffic
Lift trucks, carts, vehicles, travel paths, turns, staging areas, loading zones, and crossings.
- 02
People
Pedestrian routes, entrances, workstations, gathering points, visibility, and required egress.
- 03
Assets
Rack ends and posts, columns, doors, utilities, equipment, controls, and building infrastructure.
- 04
Exposure
Known impact history, approach direction, vehicle geometry, blind corners, and constrained areas.
- 05
Site
Slab and anchoring zones, joints, drains, embedded services, clearances, and operating conditions.
Where protection fits
High-traffic facilities with exposed people and assets
Protection systems are most useful when they are coordinated with the operating layout rather than added as isolated products. Traffic, access, sightlines, rack geometry, and facility constraints need to be reviewed together.
Connected project services
From traffic review to ongoing inspection
Connect the protection system to layout planning, installation and anchoring, inspection, and maintenance for the full project path.
01 / Plan Design + Layout
Map traffic, pedestrians, exposed assets, and required operating clearance.
→
02 / Install Professional Installation
Coordinate field layout, product placement, installation, and handoff.
→
03 / Verify the slab Concrete Scanning + Anchoring
Review anchoring locations and subsurface conditions before drilling where required.
→
04 / Inspect Safety + Compliance
Review installed conditions, damage, documentation, and required next actions.
→
05 / Maintain Repairs + Maintenance
Plan replacement or repair work after damage, impact, or operational change.
→Frequently asked questions
Planning warehouse protection
Start with the movement, exposed assets, and known conflict points. The protection details can be narrowed from there.
Why is rack protection important in warehouses?
Rack protection helps manage exposure where lift trucks, carts, and other equipment operate near storage systems. The correct protection strategy depends on the rack, traffic pattern, equipment, clearances, and site conditions; it does not replace safe operating procedures or regular inspection.
Can safety systems be added to an existing warehouse?
Often, yes. Existing conditions must be reviewed for operating clearance, access, egress, rack and building geometry, slab and anchoring conditions, embedded services, and compatibility with the proposed products.
How do you determine where protection is needed?
Begin by mapping vehicle and pedestrian routes, crossings, blind corners, staging areas, rack ends, exposed posts, columns, doors, utilities, equipment, workstations, and any known impact history. Those observations help identify priority conflict points.
Do rack guards and safety barriers need to be inspected?
Protective devices and the assets behind them should be checked as part of the facility inspection process and after a known impact. Inspection frequency and required action depend on the product, site procedures, damage, manufacturer guidance, and applicable requirements.
What information is needed for a protection-system quote?
Provide the facility city, layout or marked-up plan, photos, equipment types, traffic and pedestrian routes, known impact points, assets to protect, site constraints, and target timing. If some details are missing, send what is available.
Does Pac Rac support warehouse protection projects across Canada?
Yes. Pac Rac supports warehouse safety and rack-protection projects across Canada. Product availability, delivery, installation, and scheduling are confirmed for the facility location and project scope.
Have a layout, incident photo, or marked-up traffic plan?
Start with the conflict points
Send the available site information. Pac Rac can identify the next questions before the protection system is selected and located.
Request a quote